APS199N IDEC, APS199N Datasheet
APS199N
Specifications of APS199N
Related parts for APS199N
APS199N Summary of contents
Page 1
TWS Control Units Series ...
Page 2
TWS Control Units (Selection Guide) Series Function Flush Category Shape ABS1 Type AOS1 Page 9 Function Mushroom with Mushroom Pushlock Full Shroud Category Momentary/Maintained Shape ABGS3 Type AOGS3 Page 10 Function Square Flush Square Extended Category Momentary/Maintained Shape UBQS1 ...
Page 3
TWS Function Extended with Extended Category (Non-marking) (Non-marking) Shape ALS2 Type AOLS2 Page 15 Illuminated Function Pushbutton (LED/Incandescent) Square Flush Category (Marking) Shape ULQS1B Type UOLQS1B Page 19 Control Units (Selection Guide) Series Illuminated Pushbutton (LED/Incandescent) Extended with Half Shroud ...
Page 4
... For the control units listed below, the rated current (load switching current) is reduced to a half of the rated operational current of the con- tact block. The rated insulation voltage (600V) and the rated thermal current (10A) remain unchanged. • Selector switches and illuminated selector switches with contact code 2R, 3S, 4S, or 4R. HW-C (Contact Block) • ...
Page 5
... Pushlock turn reset: Square twin maintained: Selector switches: Electrical Life (minimum operations) Key selector switches: Illuminated selector switches: 250,000 Others: ∗1 Switching frequency 1,800 operations/h, duty ratio 40% ∗2 Switching frequency 900 operations/h, duty ratio 40% ∗3 Switching frequency 1,200 operations/h, duty ratio 40% LED Illuminated Unit Specifi ...
Page 6
... AC/DC 1W (18V) 1W (24V) 1W (30V) Note: The minimum mounting centers are applicable to switches with one layer of contact blocks (two contact blocks). When two layers of contact blocks are mounted, determine the minimum mounting centers in consideration of convenience for wiring. • ø35mm mushroom minimum • ...
Page 7
... Standard Units • Specify an operator or lens color code in the Type No. • Full voltage type illuminated units are not supplied with a lamp. Order LED or incandescent lamps separately. Transformer and DC-DC converter type illuminated units contain an LED or incandescent lamp. • All standard units are UL, CSA, EN, and TÜV approved (except DC-DC converter type). • ...
Page 8
TWS Control Units (Ordering Information) Series Selector Switch ASS Contact arrangement code Operator type (blank): Knob L: Lever Number of positions Note: • See pages for contact arrangement codes. Key Selector Switch ...
Page 9
Flush / Extended Types Operation Shape Type Flush ABS1 AOS1 Momentary Maintained Extended ABS2 AOS2 Momentary Maintained Extended with Half Shroud ABGS2 AOGS2 Momentary Maintained Extended with Full Shroud ABFS2 AOFS2 Momentary Maintained • Specify a button color code in ...
Page 10
... Other contact arrangements are also available. See page 7. • Pushlock Turn Reset: Button is maintained when pressed and is reset when turned clockwise. Note: AVS3 cannot be used as emergency stop switches. When emergency stop switches are required, use series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). ...
Page 11
... Pushbuttons with one or three contact blocks contain a dummy block. • Other contact arrangements are also available. See page 7. • Push-Pull: Button is maintained in both depressed and reset positions contact blocks (1 layer) can be mounted on AYS31 push-pull switches. • Contact Statuses of Push-Pull Switch AYS31 ...
Page 12
... Square Twin (Momentary): Two independent momentary switches are contained in one unit, each operated OFF button. With the ø30 adapter removed from the sleeve, the unit can mount in a ø25.5mm mounting hole for the ø25 series. • Square Twin (Maintained): The contact operates when ON button is pressed and is maintained in the depressed position. The button is reset by pressing the OFF button. With the ø ...
Page 13
... The lamp of push-to-check pilot light is not connected to the contact terminal. To connect, refer to the circuit diagram example below. START OLS STOP Push-to-Check Pilot Light TWS Input Type Type No. APS199N➁ Transformer APS1➂DN➁ PW DC-DC Converter∗ APS116DDN➁ Transformer APS1N➂➁ UPQS1B99N➁ Transformer UPQS1B➂ ...
Page 14
TWS Pilot Lights Series Dimensions • Dome APS1 M3.5 Terminal Screw Panel Thickness 0 22 22.5 ø34 A: Full voltage type B: Transformer type • Square (Marking Type) UPQMS1B (Metal Bezel) M3.5 ...
Page 15
... Y: • Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 35. • LED illuminated transformer and DC-DC converter types contain an LED lamp (LSTD-6➁, rated voltage 6V AC/DC). • Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). ...
Page 16
... Y: • Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 35. • LED illuminated transformer and DC-DC converter types contain an LED lamp (LSTD-6➁, rated voltage 6V AC/DC). • Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). ...
Page 17
... Y: • Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 35. • LED illuminated transformer and DC-DC converter types contain an LED lamp (LSTD-6➁, rated voltage 6V AC/DC). • Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). ...
Page 18
... W: white • Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 35. • LED illuminated transformer types contain an LED lamp (LSTD-6➁, rated voltage 6V AC/DC). • Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). ...
Page 19
... W: white Y: • Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 35. • LED illuminated transformer types contain an LED lamp (LSTD-6➁, rated voltage 6V AC/DC). • Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). ...
Page 20
TWS Illuminated Pushbuttons Series Dimensions • Round Extended ALS2 / AOLS2 M3.5 Terminal Panel Thickness 0 Screws blocks blocks blocks ), 110 ( 4 blocks) ...
Page 21
... NO • On the 2-position selector switches marked with ∗ above, the contact operation is reversed as follows. • On the contact arrangement marked with ★ in the table above, the rated current (load switching current) is reduced to a half of the rated current of the contact block. The rated insulation voltage and the rated thermal current remain unchanged. ...
Page 22
... NO • On the 2-position selector switches marked with ∗ above, the contact operation is reversed as follows. • On the contact arrangement marked with ★ in the table above, the rated current (load switching current) is reduced to a half of the rated current of the contact block. The rated insulation voltage and the rated thermal current remain unchanged. ...
Page 23
... Key retained positions are also available. See page 8. • On the 2-position selector switches marked with ∗ above, the contact operation is reversed as follows. • On the contact arrangement marked with ★ in the table above, the rated current (load switching current) is reduced to a half of the rated current of the contact block. The rated insulation voltage and the rated thermal current remain unchanged. • ...
Page 24
... On the selector switches marked with ∗ above, the contact operation is reversed as follows. • Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 35. • LED illuminated transformer types contain an LED lamp (LSTD-6➁, rated voltage 6V AC/DC). ...
Page 25
... Y: yellow • Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 35. • LED illuminated transformer types contain an LED lamp (LSTD-6➁, rated voltage 6V AC/DC). • Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). ...
Page 26
TWS Selector Switch Contact Arrangement Charts Series 90° 2-position (Maintained / Spring Return) Maintained Positions L Operator Types Contact Circuit Mounting Type Code No. Position — (1NO) 2 Dummy — (1NC) 2 ...
Page 27
TWS Selector Switch Contact Arrangement Charts Series 45° 3-position (Maintained / Spring Return) Maintained Positions C L Operator Types Operator Positions Contact Circuit Mounting Type Code No. Position 202 203 ...
Page 28
TWS Selector Switch Contact Arrangement Charts Series 45° 3-position (Maintained) Maintained Positions L Knob, Lever, Operator Types Illuminated Operator Positions Contact Circuit Mounting Type Code No. Position ★ ★ 3S 243 ...
Page 29
TWS Series Terminal Covers Terminal Cover Control Unit • Pilot light APS Full Voltage UPQS UPQMS Transformer DC-DC Converter • Pushbutton 1 contact block ABS AOS ABGS CB AOGS ABFS 2 contact blocks AOFS AKS AVS CB CB AJS AZS ...
Page 30
TWS Accessories and Replacement Parts Series Nameplates NSA, NSALO, and NFSO Dimensions Legend (mm) NSA Blank 34 Aluminium 0.8 mm thick With Legend NSALO 34 Aluminium Blank 0.8 mm thick NFSO 34 Stainless steel Blank 0.8 mm thick • ...
Page 31
... Used to tighten the round bezel when installing the TWS control unit onto a panel. 90 ø25 Series ø30 Series • Used to install and remove LED/incandescent lamps. OR-55 59 • Used to remove contact blocks, transformers, lenses and adapters. 130 • Used to tighten the locking ring on the square control units ...
Page 32
... Temperature range: –5 to +60ºC OCS-11➀ OCS-11➀ 1 • Used to protect momentary and maintained pushbuttons, illuminated pushbuttons, knob selector switches, and key selector switches. OLS-KL1 OLS-KL1 1 • Used to protect flush buttons from inadvertent operation. • Can be easily attached under the round bezel. ...
Page 33
TWS Series Maintenance Parts Shape Bezel Pushbutton Pilot Light Selector Switch Pushbutton Pilot Light Selector Switch Pushbutton with Full Shroud Mushroom with Full Shroud Pushbutton, Illumi- nated Pushbutton with Half Shroud Illuminated Pushbut- ton with Full Shroud Button Flush Extended ...
Page 34
TWS Accessories and Replacement Parts Series Maintenance Parts Shape Selector Operator Knob Lever Color Insert Illuminated Selector Cap for Key Selector Clear Button Cover Marking Plate Marking Plate For Square Pilot Lights and Illumi- nated Pushbuttons For Square Pilot ...
Page 35
... Current Draw Operating Voltage AC 6V AC/DC ± (G, PW, S) 5.5 mA (G, PW, S) 12V AC/DC ±10 24V AC/DC ±10 Incandescent Lamps (LS Type) Rated Operating Voltage Lamp Ratings 6V AC/DC 1W (6.3V) 12V AC/DC 1W (18V) 18V AC/DC 1W (24V) 24V AC/DC 1W (30V) Transformer Shape Primary Voltage Transformer Unit ...
Page 36
... Failure to turn power off may cause electrical shocks or fire hazard. • To avoid a burn on your hand, use the lamp holder tool when replacing lamps. • For wiring, use wires of a proper size to meet the voltage and current requirements. Tighten the M3.5 terminal screws to a tightening torque of 1.0 to 1.3 tighten terminal screws may cause overheat and fi ...
Page 37
... Marking Plate (White) Marking Plate (Transparent) Lens Holder Replacement of Lamps Lamps can be replaced by using the lamp holder tool (OR- 55) from the front of the panel. • How to remove To remove, slip the lamp holder tool onto the lamp head lightly. Then push slightly, and turn the lamp holder tool counterclockwise. • ...
Page 38
TWS Instructions Series Instructions Panel Thickness and Rubber Washer Adjust the thickness of the rubber washers according to the panel thickness. Also, make sure to include the nameplate thickness when using a nameplate. Applicable Models • Momentary Type Pushbutton ...
Page 39
... When using LED lamps, observe the following instructions. • Rated Voltage The LED lamps are rated at 6V, 12V, or 24V AC/DC, and can be used within ±10% the rated voltage of either AC or DC. • DC Power 1. Switching power supply Regulated voltage from switching power supply is best suited ...
Page 40
... Specifications and other descriptions in this catalog are subject to change without notice. IDEC CORPORATION (USA) 1175 Elko Drive, Sunnyvale, CA 94089-2209, USA Tel: +1-408-747-0550, Toll Free: (800) 262-IDEC, Fax: +1-408-744-9055 E-mail: opencontact@idec.com, www.idec.com IDEC CANADA LIMITED Unit 22-151, Brunel Road Mississauga, Ontario, L4Z 1X3, Canada ...