DS18S20Z Maxim Integrated Products, DS18S20Z Datasheet - Page 20

• Manufacturer Part Number: DS18S20Z
• Description: IC THERM MICROLAN HI-PREC 8-SOIC
• Manufacturer: Maxim Integrated Products

Specifications of DS18S20Z

• Sensing Temperature: -55°C ~ 125°C
• Output Type: Digital
• Voltage - Supply: 3 V ~ 5.5 V
• Accuracy: ±0.5°C
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Full Temp Accuracy: +/- 2 C
• Digital Output - Bus Interface: Serial (1-Wire)
• Digital Output - Number Of Bits: 9 bit
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Pin Relative to Ground ........................................................................................ -0.5V to +6.0V
Continuous Power Dissipation (T
Operating Temperature Range ................................................................................................................ -55°C to +125°C
Storage Temperature Range .................................................................................................................... -55°C to +125°C
Lead Temperature (soldering, 10s) .......................................................................................................... +260°C
Soldering Temperature (reflow)
These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability.
DC ELECTRICAL CHARACTERISTICS
(V
NOTES:
1) All voltages are referenced to ground.
2) The Pullup Supply Voltage specification assumes that the pullup device is ideal, and therefore the high level of
3) See typical performance curve in
4) Logic-low voltages are specified at a sink current of 4mA.
5) To guarantee a presence pulse under low voltage parasite power conditions, V
6) Logic-high voltages are specified at a source current of 1mA.
7) Standby current specified up to +70°C. Standby current typically is 3µA at +125°C.
8) To minimize I
9) Active current refers to supply current during active temperature conversions or EEPROM writes.
10) DQ line is high (“high-Z” state).
11) Drift data is based on a 1000-hour stress test at +125°C with V
Supply Voltage
Pullup Supply
Voltage
Thermometer Error
Input Logic-Low
Input Logic-High
Sink Current
Standby Current
Active Current
DQ Input Current
Drift
8-Pin SO (derate 5.9mW/°C above +70°C) .......................................................................................... 470.6mW
3-Pin TO-92 (derate 6.3mW/°C above +70°C)..................................................................................... 500mW
Containing lead(Pb) ............................................................................................................................ +240°C
DD
Lead(Pb)-free ..................................................................................................................................... .+260°C
PARAMETER
the pullup is equal to V
pullup transistor must include margin for the voltage drop across the transistor when it is turned on; thus:
V
as low as 0.5V.
V
= 3.0V to 5.5V, T
PU_ACTUAL
DD
– 0.3V ≤ DQ ≤ V
= V
DDS
PU_IDEAL
, DQ should be within the following ranges: GND ≤ DQ ≤ GND + 0.3V or
A
= -55°C to +125°C, unless otherwise noted.)
SYMBOL
DD
PU
+ V
V
.
V
t
I
V
V
I
I
. In order to meet the V
ERR
DDS
I
DD
DQ
DD
A
PU
L
IL
IH
TRANSISTOR
= +70°C)
Figure 16
Local Power
Parasite Power
Local Power
-10°C to +85°C
-55°C to +125°C
Local Power
Parasite Power
V
V
CONDITIONS
I/O
DD
.
= 0.4V
= 5V
.
IH
20 of 23
spec of the DS18S20, the actual supply rail for the strong
MIN
+3.0
+3.0
+3.0
+2.2
+3.0
-0.3
4.0
DD
= 5.5V.
TYP
±0.2
750
1
5
The lower of
V
ILMAX
DD
MAX
1000
+5.5
+5.5
±0.5
+0.8
V
5.5
1.5
±2
or
DD
+ 0.3
may have to be reduced to
UNITS
mA
mA
µA
nA
°C
°C
V
V
V
V
NOTES
DS18S20
1, 4, 5
1, 2
1, 6
7, 8
10
11
1
3
1
9