JM38510/31202B2A National Semiconductor, JM38510/31202B2A Datasheet
JM38510/31202B2A
Specifications of JM38510/31202B2A
Available stocks
Related parts for JM38510/31202B2A
JM38510/31202B2A Summary of contents
Page 1
MICROCIRCUITS, DIGITAL, LOW-POWER SCHOTTKY TTL, 4-BIT BINARY FULL ADDERS WITH FAST CARRY, MONOLITHIC SILICON This specification is approved for use by all Departments 1. SCOPE 1.1 Scope. This specification covers the detail requirements for monolithic silicon, low-power Schottky TTL, 4-bit ...
Page 2
Absolute maximum ratings. Supply voltage range ............................................................................. -0 7 Input voltage range ................................................................................ - Storage temperature range .................................................................... -65 to +150 C Maximum power dissipation ...
Page 3
REQUIREMENTS 3.1 Qualification. Microcircuits furnished under this specification shall be products that are manufactured by a manufacturer authorized by the qualifying activity for listing on the applicable qualified manufacturers list before contract award (see 4.3 and 6.4). 3.2 Item ...
Page 4
Test High level output voltage Low level output voltage Input diode clamp voltage Low level input current at any input Low level input current at C input 0 High level input current at any ...
Page 5
TABLE I. Electrical performance characteristics - Continued. Test Propagation delay time, to ∑ high-to-low level Propagation delay time, to ∑ low-to-high level Propagation delay time, high-to-low level Propagation delay ...
Page 6
Interim electrical parameters Final electrical test parameters Group A test requirements Group B electrical test parameters when using method 5005 QCI option Group C end-point electrical parameters Group D end-point electrical parameters *PDA applies to subgroup 1. 4.3 Qualification inspection. ...
Page 7
MIL-M-38510/312C Terminal symbol device type 01 Terminal Case Case number ∑ ∑ ∑ ...
Page 8
INPUT ...
Page 9
MIL-M-38510/312C FIGURE 3. Logic diagram. 9 ...
Page 10
MIL-M-38510/312C FIGURE 3. Logic diagram - Continued. 10 ...
Page 11
NOTES: 1. The pulse generator has the following characteristics: PRR t = 200 ns and OUT 10% including scope probe, wiring, and stray capacitance without package in test fixture ...
Page 12
Terminal conditions (pins not designated may be high Cases MIL-STD Subgroup Symbol 883 Case method 2 ∑ 3 Test no 3006 1 2 ...
Page 13
Terminal conditions (pins not designated may be high Cases MIL-STD Subgroup Symbol 883 Case method 2 Test no. A4 ∑ 3005 52 GND GND CC1 I " ...
Page 14
Terminal conditions (pins not designated may be high Cases MIL-STD Subgroup Symbol 883 Case method 2 Test no. A4 ∑ 3003 101 PHL6 ...
Page 15
Terminal conditions (pins not designated may be high Cases MIL-STD Subgroup Symbol 883 Case method 2 ∑ 2 Test no 3006 1 2 ...
Page 16
Terminal conditions (pins not designated may be high Cases MIL-STD Subgroup Symbol 883 Case method 2 ∑ 2 Test no 3005 52 GND GND CC1 I " ...
Page 17
Terminal conditions (pins not designated may be high Cases MIL-STD Subgroup Symbol 883 Case method 2 ∑ 2 Test no 3003 101 OUT GND IN PHL6 Tc ...
Page 18
PACKAGING 5.1 Packaging requirements. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel performed by DoD personnel, these personnel need to contact the ...
Page 19
Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535, MIL-HDBK-1331, and as follows: GND ........................................... Ground zero voltage potential. I ................................................ Current flowing into an input terminal ............................................... Voltage level at ...
Page 20
STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL 1. The preparing activity must complete blocks and 8. In block 1, both the document number and revision letter should be given. 2. The submitter of this form must complete blocks 4, 5, ...