ACFM-7107 Avago Technologies, ACFM-7107 Datasheet
ACFM-7107
Available stocks
Related parts for ACFM-7107
ACFM-7107 Summary of contents
Page 1
... This process allows the filters to be assembled in a module with a footprint of only with a maximum height of 1.2 mm. Low Tx Insertion Loss of the ACFM-7107 reduces power amplifier current, extending battery life and talk time. The ACFM-7107 enhances receiver sensitivity and dynamic range with low Rx Insertion Loss and high rejection of Tx signals at the Rx ports ...
Page 2
... ACFM-7107 Electrical Specifications, Z Symbol Parameter Cellular Duplexer Performance Antenna Port to Cellular Receive Po rt S41 Insertion Loss in Rx band (869–894 MHz) S41 Insertion Loss Ripple (p- Band (869–894 MHz) S41 Attenuation in Tx band (824–849 MHz) S41 Attenuation 0–804 MHz ...
Page 3
... ACFM-7107 Electrical Specifications Symbol Parameter PCS Duplexer Performance Antenna Port to PCS Receive Port S31 Insertion Loss in Rx Band (1930.5–1989.5 MHz) S31 Insertion Loss Ripple (p- Band S31 Attenuation in Tx Band (1850.5–1909.5 MHz) S31 Attenuation 0.03–1770 MHz S31 Attenuation 2025–3500 MHz S31 Attenuation 3500– ...
Page 4
... Figure 1. Matching Components The nominal values for L and C shown here were selected to match the ACFM-7107 to 50 ohms. Since every appli- cation is different, these nominal values may need to be adjusted to provide the best impedance match for the user’s particular circuit board, performance requirements, and interface to related components ...
Page 5
... ACFM-7107 Typical Performance at T 0.0 -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 1860 1870 1880 Frequency (MHz) Figure 2. PCS Tx Band Insertion Loss. 0 -10 -20 -30 -40 -50 -60 -70 1750 1800 1850 1900 1950 Frequency (MHz) Figure 4. PCS Tx Rejection in Rx Band and Rx Rejection in Tx Band -10 -12 -14 -16 -18 -20 1750 1800 ...
Page 6
Frequency (MHz) Figure 8. PCS Tx–Ant and Ant–Rx Wideband Insertion Loss. -20 -30 -40 -50 -60 -70 -80 2000 2500 3000 Frequency (MHz) Figure 10. PCS Ant–Rx Rejection, 2000–4000 ...
Page 7
Frequency (MHz) Figure 14. Cellular Tx Insertion Loss. 0 -10 -20 -30 -40 -50 -60 -70 800 850 Frequency (MHz) Figure 16. Cellular Tx Rejection in Rx Band and Rx ...
Page 8
Frequency (MHz) Figure 20. Cellular Tx–Ant and Ant–Rx Wideband Insertion Loss. -55 -56 -57 -58 -59 -60 -61 -62 -63 -64 -65 1650 1660 1670 Frequency (MHz) Figure 22. ...
Page 9
Frequency (MHz) Figure 26. GPS Band Rejection, Cellular Tx–Ant. Notes: 1. Performance shown includes effect of 5.1 nH inductor and 1.0 pF capacitor added to Port 1 (Ant) via ...
Page 10
PACKAGE ORIENTATION ANT Cell PCS Cell PCS 7.0 TOP VIEW Notes: 1. Dimensions Tolerance: X.X ±0.1, X.XX ± 0.05 3. Max OD: 4.1 x 7 pads (5 ea), ...
Page 11
X 1.06 4.26 Notes: 1. Dimensions in mm. 2. Areas shown are location of transmit filters. Adequate heat sinking should be provided for these areas by means of ground/thermal vias. Heat sink areas on the PCB should be larger ...
Page 12
... Includes provision for series inductor and shunt capacitor (0402 size) at Ant terminal. Figure 32. Recommended PCB Layout (top view). Notes: 1. Antenna matching components shown are 0402 size. Figure 33. PCB Layout with ACFM-7107 and Ant Matching Components Superposed (top view). 12 ø 0.3 GND VIAS ON 0.54 HORIZ x 0.50 VERT GRID ...
Page 13
... Figure 34. Recommended Solder Mask (top view). The recommended solder mask is a non-solder mask defined (NSMD) pattern for SMT assembly of the ACFM- 7107. The 4.00 X 7.00 mm middle opening of the solder mask is centered on the ACFM-7107 PCB location. The openings in the solder mask allow a clearance of 0. 0.55 ...
Page 14
... C A 0.18 1.25 2.33 3.40 4.48 5.55 6.63 6.80 Stencil Opening ID Qty A (I/O pad areas Figure 35. Recommended Solder Stencil (top view). The I/O pad openings (“A”) in the recommended solder stencil are the same size as the I/O pad metal patterns on the ACFM-7107 Width Height 0.35 0.35 0.40 2.00 0.80 ...
Page 15
... Figure 36. Solder Stencil Superposed on ACFM-7107 Bottom Metal Pattern. (top view) Figure 38. Solder Mask Superposed on ACFM-7107 Bottom Metal Pattern. (top view) 15 Figure 37. Solder Mask Superposed on Solder Stencil. (top view) ...
Page 16
... Figure 39. Verified SMT Solder Profile. PCS Cell Tx Tx ANT Figure 40. Package Marking 16 Performance Level 3 200 250 300 PROFILE GRF PROFILE WMF 6 February 2003 R. Waugh PACKAGE PCS Cell ORIENTATION Rx Rx ACFM-7107 = Part Number FB = Mfg Information Y = Year WW = Work Week DD = Date Code XXXX = Assembly Lot ...
Page 17
Figure 41. SMT Tape Packing PACKAGE ORIENTATION POCKET CAVITY Figure 42. Orientation in Tape 17 SPROCKET HOLES ...
Page 18
... Part Number No. of Devices ACFM-7107-BLK 25 ACFM-7107-TR1 1000 For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2009 Avago Technologies. All rights reserved. ...