IRDCIP2005C-2 International Rectifier, IRDCIP2005C-2 Datasheet
IRDCIP2005C-2
Specifications of IRDCIP2005C-2
Related parts for IRDCIP2005C-2
IRDCIP2005C-2 Summary of contents
Page 1
Features • 40A Multiphase building block • No derating PCB • Optimized for low power loss • Bias supply range of 4.5V to 7.0V • Operation up to 1.5MHz • Bi-directional current flow • Under Voltage Lockout ...
Page 2
Absolute Maximum Ratings V to PGND ……………………..……...-0.5V to 16. PGND …………………….….…..-0.5V to 7.5V DD PWM to PGND ………………….………-0. ENABLE to PGND …………………….. -0. Storage Temperature …………………. -60ºC to 150ºC Block Temperature….. …………………. -40ºC ...
Page 3
PARAMETER Supply Current (Stand By) Supply Current (Operating) Power-On Reset (POR) V Rising DD V Falling DD Hysteresis ENABLE INPUT Logic Level Low Threshold ( Logic Level High Threshold ( Threshold Hysteresis Weak Pull-down impedance Rising ...
Page 4
Power Loss Curve 12V 5. 1. 1MHz 300nH 125ºC BLK ...
Page 5
Typical Performance Curves 1.30 1.25 1.20 1.15 1.10 1.05 1.00 0.95 0.90 2.5 4 5.5 7 8.5 10 Input Voltage (V) Figure 3 Normalized Power Loss vs. Input Voltage 1.04 1.03 1.02 1.01 1.00 0.99 0.98 0.1 0.2 0.3 0.4 ...
Page 6
Average Average Average Average VDD Current A Average DC ...
Page 7
... It incorporates the ability to solve thermal problems where heat is drawn out through the printed circuit board and the top of the case. Please refer to International Rectifier Application Note AN1047 for further details on using this SOA curve in your thermal environment. ...
Page 8
Calculating Power Loss and SOA for Different Operating Conditions To calculate Power Loss for a given set of operation conditions, the following procedure should be followed: Power Loss Procedure 1. Determine the maximum current and obtain the maximum power loss ...
Page 9
Calculating SOA Temperature: (Figure 3) SOA temperature adjustment for input voltage ≈ -0.6ºC (Figure 5) SOA temperature adjustment for output inductor ≈ 0.25 ºC (Figure 6) SOA temperature adjustment for switch frequency ≈ -2.5 ºC axis intercept adjustment ≈ -0.6 ...
Page 10
Internal Block Diagram Pin Description Pin Number Pin Name PGND PWM 6 ENABLE 7,8 N/C Notes recommended to connect PIN 7 and 8 to PIN 1 ...
Page 11
Recommended PCB Layout A Figure 13 Top copper and Solder-mask layer of PCB layout www.irf.com GND 3 A 04/09/2009 iP2005CPbF PD-60360 N/C 8 N/C 7 ENABLE 6 PWM Copper ...
Page 12
... The following guidelines are recommended to reduce the parasitic values and optimize overall performance. • All pads on the iP2005C footprint design need to be Solder-mask defined (see Figure 13). Also refer to International Rectifier application notes AN1028 and AN1029 for further footprint design guidance. • Place as many vias around the Power pads (V thermal performance. • ...
Page 13
Mechanical Outline Drawing 0.15 [.006] C 7.65 [.301] CORNER ID TOP VIEW 3.48 [.137] 0.31 [.012] 0.31 [.012] 4X 0.66 [.026] 5X 0.89 [.035] 1.78 [.070] 3X 3.86 [.152] BOTTOM VIEW www.irf.com B A 7.65 [.301] 0.15[.006] C 0.07 [.0027] ...
Page 14
Figure 16 Tape and Reel Information 04/09/2009 iP2005CPbF PD-60360 14 ...
Page 15
Recommended Solder Paste Stencil Design CORNER ID Figure 17 Solder Paste Stencil Design The recommended reflow peak temperature is 260°C. The total furnace time is approximately 5 minutes with approximately 10 seconds at peak temperature. www.irf.com Figure 18 Part Marking ...