PIC18LF452 Microchip Technology, PIC18LF452 Datasheet - Page 182

• Manufacturer Part Number: PIC18LF452
• Description: (PIC18LFxx2) Enhanced FLASH Microcontrollers
• Manufacturer: Microchip Technology

PIC18FXX2
16.4.2
The operation of the Synchronous Master and Slave
modes is identical, except in the case of the SLEEP
mode and bit SREN, which is a “don't care” in Slave
mode.
If receive is enabled by setting bit CREN prior to the
SLEEP instruction, then a word may be received during
SLEEP. On completely receiving the word, the RSR
register will transfer the data to the RCREG register,
and if enable bit RCIE bit is set, the interrupt generated
will wake the chip from SLEEP. If the global interrupt is
enabled, the program will branch to the interrupt vector.
TABLE 16-11: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
DS39564B-page 180
INTCON
PIR1
PIE1
IPR1
RCSTA
RCREG
TXSTA
SPBRG
Legend: x = unknown, - = unimplemented, read as '0'.
Note 1: The PSPIF, PSPIE and PSPIP bits are reserved on the PIC18F2X2 devices; always maintain these bits
Name
Shaded cells are not used for Synchronous Slave Reception.
clear.
USART SYNCHRONOUS SLAVE
RECEPTION
USART Receive Register
Baud Rate Generator Register
PSPIE
PSPIP
PSPIF
SPEN
CSRC
GIEH
Bit 7
GIE/
(1)
(1)
(1)
PEIE/
ADIE
ADIP
GIEL
ADIF
Bit 6
RX9
TX9
TMR0IE INT0IE
SREN
TXEN
RCIF
RCIE
RCIP
Bit 5
CREN
SYNC
Bit 4
TXIF
TXIE
TXIP
ADDEN
SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
SSPIP CCP1IP TMR2IP TMR1IP 0000 0000 0000 0000
SSPIF
RBIE
Bit 3
—
TMR0IF INT0IF
CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
BRGH
FERR
Bit 2
To set up a Synchronous Slave Reception:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Enable the synchronous master serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
If interrupts are desired, set enable bit RCIE.
If 9-bit reception is desired, set bit RX9.
To enable reception, set enable bit CREN.
Flag bit RCIF will be set when reception is com-
plete. An interrupt will be generated if enable bit
RCIE was set.
Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
If any error occurred, clear the error by clearing
bit CREN.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
OERR
TRMT
Bit 1
RX9D
TX9D
RBIF
Bit 0
2002 Microchip Technology Inc.
0000 000x 0000 000u
0000 -00x 0000 -00x
0000 0000 0000 0000
0000 -010 0000 -010
0000 0000 0000 0000
POR, BOR
Value on
All Other
Value on
RESETS